5.08mm ptich wire to wire and wire to board Crimp Terminal,#18 - #24 AWG,gold plating terminals C5080M-T-A
1, The specification of the product including basic size information, electrical and mechanical properties.
| Basic size information |
| Termination Interface Style | Crimp |
| Processing methods | E-stamping before Gold-flash |
| Insulation O.D. | 0.60mm(Max) |
| Part No. | A1006-GPE |
| Application | Signal, PCB board |
| |
| Electrical properties |
| Current Rating | 1A AC, DC |
| Voltage Rating | 200V AC, DC |
| Contact Resistance | 40mΩ Max |
| Insulation Resistance | 100MΩ min |
| Withstanding Voltage | 500V AC/minute |
| |
| Mechanical properties |
| Temperature range | -25℃ to 85 ℃ |
| Other information please kindly check the following picture. |
2, Related drawing and report
The following pictures are engineering drawing and testing report for your reference, wish these can help you to purchase the ideal and right parts from us. Thank you!
| 1. Scope This specification covers the requirements for product performance of 1.00mm pitch wire to board connectors series. 2. Construction,Dimensions,Material & Plating See the attached drawings 3. Ratings & Applicable Wires | Item | Standard | | Rated Voltage (Max.) | 200V AC/DC | Insulation O.D. 0.60mm (Max.) | | Rated Current (Max.) And Applicable Wires | AWG#30 | 1A AC/DC | | AWG#32 | 0.8A AC/DC | | AWG#34 | 0.5A AC/DC | | Ambient Temperature Range | -25℃ ~ +85℃* | *: Including terminal temperature rise 4. Electrical Performance | Test Description | Procedure | Requirement | | 4-1 | Contact Resistance | Mate connectors, measure by dry circuit, 20mV max., 10mA.(Based upon JIS C5402 5.4) | 35mΩ (Max.) | | 4-2 | Insulation Resistance | Mate connectors, apply 200V DC between adjacent terminal or ground. (Based upon JIS C5402 5.2/MIL-STD-202 Method 302 Cond. B) | 100MΩ (Min.) | | 4-3 | Dielectric Withstanding Voltage | Mate connectors, apply 500V AC (rms) for 1 minute between adjacent terminal or ground. (Based upon JIS C5402 5.1/MIL-STD-202 Method 301) | No Breakdown. | | 4-4 | Contact Resistance on Crimped Portion | Crimp the applicable wire on to the terminal, measure by dry circuit, 20mV (Max.)., 10mA. | 5mΩ (Max.) | 5. Mechanical Performance | Test Description | Procedure | Requirement | | 5-1 | Actuator Insertion & Withdrawal Force | Insert and withdraw connectors at the speed rate of 25±3mm / minute. | Refer to paragraph 7 | | 5-2 | Crimping Pull Out Force | Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) | AWG#30 | 0.8kgf (Min) | | AWG#32 | 0.5kgf (Min) | | AWG#34 | 0.3kgf (Min) | | 5-3 | Terminal Insertion Force. | Insert the crimped terminal into the housing. | 0.50kgf (Max.) | | 5-4 | Terminal/Housing Retention Force. | Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. | 0.50kgf (Min.) | | 5-5 | Pin Retention Force | Apply axial push force at the speed rate of 25±3mm / minute | 0.40kgf (Min.) | | 5-6 | Durability | When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. | Contact Resistance 80mΩ (Max.) | | 5-7 | Vibration | Amplitude: 1.5mm P-P Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes. (Based upon MIL-STD-202 Method 201A) | Appearance No Damage. Contact Resistance 80mΩ (Max.) Discontinuity 1 μsec.(Max.) | | 5-8 | Physical Shock | 490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) | |
| 6. Environmental Performance And Others | Test Description | Procedure | Requirement | | 6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) | | 6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) | Appearance No Damage. Contact Resistance 80mΩ (Max.) | | 6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) | | 6-4 | Humidity | Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) | Appearance No Damage. Contact Resistance 80mΩ (Max.) Insulation Resistance 10MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 | | 6-5 | Temperature Cycling | 5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025) | Appearance No Damage. Contact Resistance 80mΩ (Max.) | | 6-6 | Salt Spray | Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) | | 6-7 | SO2 Gas | 24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. | | 6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | | 6-9 | Solderability | Soldering Time: 5±0.5 sec. Solder Temperature: 245±5℃ | Solder Wetting 95% of immersed area must show no voids, pin holes | | 6-10 | Resistance to Soldering Heat | When reflowing Refer to paragraph 8 Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ | Appearance No Damage. | 7. Actuator Insertion/Withdrawal Force [Unit : kgf] | Circuits | At Initial | | Insertion (Max.) | Withdrawal (Min.) | | 20 | 2.60 | 0.60 | | 30 | 4.00 | 0.76 | |
3, Benefits you can get
MOQ: If have stock, according to the smallest package. If not, according to the produce MOQ.
R&D ability:ODM&OEM is avaiable. We also can help you design molds and produce products.
Delivery time:3 to 8 days according to your order amount.
Quality Control: Original connector or replace connector we'll be 100% inspected before dispatching.
Package:PE Bag or Nylon Bag with Carton or according to you
Company Type : Factory and trade integration more than 12-years connector mold design and produce experience.
Product Tags:
|
|
1.0mm pitch FI-X gold-flash crimp terminals with phosphor bronze material for AWG30# to 34# Images
|
